Competent Person in Health and Safety: A UK Guide
What makes a competent person in health and safety under MHSWR and CDM 2015, when to use outside help, and who should review and approve a RAMS on your site.

The RAMS lands on the principal contractor's desk on a Friday afternoon. It's tidy, the headings are right and the hazards look sensible. Then the site manager asks one question: who checked this, and what makes them competent to? If nobody can answer, the job doesn't start on Monday.
A competent person in health and safety is someone with sufficient training and experience or knowledge and other qualities to properly help an employer meet their health and safety duties. That's the test in regulation 7 of the Management of Health and Safety at Work Regulations 1999 (MHSWR). Every employer must appoint at least one, an in-house person should be used ahead of an outsider where one is available, and the employer keeps the legal duty whoever they appoint. No single certificate makes someone competent. It depends on the risks and the task in front of them.
This guide covers what the law actually says, how competence works under CDM 2015, when to bring in outside help, and who should be putting their name to your RAMS.
What the law says about a competent person
The main duty sits in regulation 7 of MHSWR. It's short, and worth reading in full. In plain terms:
- Regulation 7(1): every employer must appoint one or more competent persons to help them do what health and safety law requires.
- Regulation 7(3): there must be enough of them, with enough time and resources, for the size of the business and the risks involved.
- Regulation 7(5): a person is competent if they have "sufficient training and experience or knowledge and other qualities" to assist properly.
- Regulation 7(8): if there's a competent person in your own employment, you appoint them in preference to someone from outside.
- Regulations 7(6) and 7(7): a self-employed person working alone, or a partnership where a partner has the right competence, can handle it themselves rather than appoint someone else.
Regulation 7 doesn't stand alone. Regulation 3 requires a suitable and sufficient risk assessment, and the competent person is who helps you get there. Above all of this sit the general duties in the Health and Safety at Work etc. Act 1974, which stay with the employer.
That last point matters more than people think. Appointing a competent person doesn't hand over your legal responsibility. The HSE is blunt about it: as the employer, managing health and safety is still your legal duty, even if you use someone from outside your business.
Competent person health and safety: the four ingredients
Regulation 7(5) gives you the ingredients, and the HSE describes competence as a combination of skills, experience and knowledge. On site, that breaks down like this.
Training
Formal training gives someone the framework. NEBOSH, IOSH Managing Safely, SMSTS and SSSTS all have their place, as do trade qualifications and specialist courses for things like asbestos, confined spaces or scaffold inspection. But the law doesn't name a qualification, and a certificate on its own doesn't make anyone competent. A NEBOSH diploma holder who's only worked in offices isn't automatically the right person to review a demolition RAMS.
Experience
Experience is what lets someone look at a method statement and spot that the sequence is wrong, or that the crane can't get where the drawing says it will. It's the difference between knowing what the regulations say and knowing what goes wrong on a wet Tuesday in February.
Knowledge
The competent person needs to know the relevant law and guidance for the work, the hazards of the task, and what good control looks like. That includes knowing when they're out of their depth.
Other qualities
This is the part people skip. It covers things like judgement, communication and the confidence to say no. A competent person who won't challenge the contracts manager when the programme is squeezing the method isn't much use.
The key thing is that competence is relative. The HSE says the level of competence needed depends on the complexity of the situation and the help you need. The person who's perfectly competent to review a RAMS for internal decorating in an empty office may not be competent for a live-traffic highways job.
Competence under CDM 2015
Construction has its own layer. Regulation 8 of the Construction (Design and Management) Regulations 2015 says that designers and contractors (including principal designers and principal contractors) must have the skills, knowledge and experience needed for the role. If they're an organisation, they also need the organisational capability to do it safely.
Two more parts of regulation 8 catch people out:
- A designer or contractor must not accept an appointment unless they meet those conditions.
- Whoever appoints a designer or contractor must take reasonable steps to satisfy themselves that they do.
So competence under CDM runs both ways. The client or principal contractor checks the subcontractor, and the subcontractor shouldn't take on work they can't do safely. In practice, many clients use pre-qualification questionnaires or third-party accreditation schemes to check this. Those help, but they check the company, not the individual doing the review on a given job.
Our CDM Regulations 2015 guide goes through the duty holders in more detail.
When the law names a competent person for a task
Beyond the general duty, several regulations require a competent person for specific jobs. A few you'll come across regularly:
- Scaffold and working platform inspections. Under regulation 12 of the Work at Height Regulations 2005, inspections must be carried out by a competent person, and a working platform used for construction work where someone could fall 2 metres or more must have been inspected in that position within the previous 7 days.
- Lifting equipment. LOLER requires thorough examinations to be carried out by a competent person. See our LOLER guide.
- Work equipment. PUWER has its own inspection duties. Rather than repeat it here, our PUWER guide has a full section on the competent person under PUWER.
- Electrical work. Regulation 16 of the Electricity at Work Regulations 1989 says nobody should do work where technical knowledge or experience is needed to prevent danger unless they have it, or are suitably supervised.
- Gas work. Under the Gas Safety (Installation and Use) Regulations 1998, businesses doing work on gas fittings must be members of the Gas Safe Register, and the engineers doing the work must be competent.
The general principle holds in every case. Competence is tied to the task, not to a job title.
In-house or external advice?
The law's starting point is in-house. Regulation 7(8) says use your own competent person if you have one, and the HSE adds that this can include the employer themselves. For a lot of small contractors and FM teams, the owner or an experienced supervisor is the right person, backed up with training.
You may need outside help when the business is large, complex or high risk, or when you don't have the competence in-house for a particular job. The HSE's own guidance on using a consultant says the same. Typical examples:
- A roofing contractor taking on its first job involving fragile roof lights and a public footpath below.
- An FM provider picking up a contract with a legionella risk it hasn't managed before.
- A security company asked to put together RAMS for a large event with crowd management and vehicle access.
If you go external, the Occupational Safety and Health Consultants Register (OSHCR) is a good place to start. It's a public register of UK health and safety consultants, set up after the Government's 2010 "Common Sense, Common Safety" report, and it's now run by IOSH. Consultants on it have to meet the register's eligibility criteria. Even so, check they know your sector. A consultant who specialises in manufacturing may not be the right fit for a scaffolding firm.
Whichever route you take, make sure the competent person gets the information they need. Regulation 7(4) requires employers to give external appointees the relevant health and safety information about the business.
Who can sign off a RAMS?
This is the question we get asked most. There's no regulation that says a RAMS must be signed by a named grade of person. What the law requires is a suitable and sufficient risk assessment, made with competent help, and a safe system of work that's actually followed.
In practice, a RAMS sign-off on a construction or FM job usually looks like this:
- Prepared by the contractor doing the work, ideally by someone who knows the task and has seen the site.
- Reviewed and approved by someone competent for that task and its risks. That's often a contracts manager or supervisor, with input from an H&S adviser on higher-risk work.
- Checked by the principal contractor or client to make sure it fits the construction phase plan, site rules and neighbouring trades.
- Briefed to the people doing the work, with a signed record that they've understood it.
The signature only means something if there's a real review behind it. HSE inspectors look for evidence that the RAMS has been thought about for this site, not just produced. Our post on what HSE inspectors look for in risk assessments covers what that evidence looks like, and "no evidence of competent person review" is one of the RAMS mistakes that get documents rejected.
Examples from site
Construction. A groundworks subcontractor's contracts manager, who's run deep drainage jobs for fifteen years, reviews a RAMS for a 3-metre trench next to a live road. He's competent for that. The same person reviewing a RAMS for asbestos removal would be outside his lane, and should say so.
Security. An operations manager for an event security company reviews the RAMS for a stadium concert. An SIA licence shows someone is licensed to work in security. It doesn't, by itself, show they're competent to assess crowd crush risk or vehicle movements in the loading area. That needs specific experience or specialist input.
Facilities management. An FM supervisor receives a contractor's RAMS for roof plant maintenance. Their job isn't to rewrite it, but they do need enough competence to spot that it says nothing about the fragile roof lights they know are there. If they don't have that competence for a particular job, they should get someone who does to look at it.
Can software be the competent person?
No. Regulation 7 is about appointing a person with training, experience, knowledge and other qualities. Software can't visit the site, can't see that the ground's been churned up by last week's rain, and can't take responsibility for a decision.
AI tools can be genuinely useful for drafting. They're quick at setting out the structure of a RAMS, suggesting hazards commonly associated with a task, and citing the relevant legislation. But everything they produce is a draft. A competent person has to review it against the actual site and task, edit what doesn't fit, and approve it before anyone works to it. We go into this in more detail in what AI RAMS is and isn't.
Be wary of anyone who tells you a tool removes the need for competent review. It doesn't, and the law doesn't allow it to.
How swiftRMS helps
swiftRMS is RAMS software that drafts risk assessments and method statements for UK construction, security and FM work. You describe the job and it produces a structured, legislation-referenced draft, ready for review.
That draft is where your competent person starts, not where they finish. They check it against the site, edit the hazards and controls to match what's really there, and approve it before it's issued. The time they'd have spent typing headings and hunting for regulation numbers goes on the part that needs their judgement. You can see the format in our example RAMS.
swiftRMS doesn't replace your competent person, and it isn't one.
If you want to see what a draft looks like before your reviewer gets hold of it, try a free RAMS preview with no signup. If it suits your team, there's a 14-day free trial with no card needed.
Frequently Asked Questions
What is a competent person in health and safety?
It's someone with sufficient training and experience or knowledge and other qualities to properly help an employer meet their health and safety duties. That definition comes from regulation 7(5) of the Management of Health and Safety at Work Regulations 1999. The level of competence needed depends on the work and the risks involved.
Is a competent person a legal requirement?
Yes. Regulation 7 of MHSWR requires every employer to appoint one or more competent persons to help them comply with health and safety law. The exceptions are a self-employed person working alone, or a partnership where one of the partners has the right competence, who can do it themselves.
Does a competent person need a qualification?
The law doesn't name one. Qualifications like NEBOSH or SMSTS are good evidence of training, but competence also needs relevant experience, knowledge of the task and the judgement to apply it. Someone can hold a qualification and still not be competent for a particular high-risk job.
Can the employer be the competent person?
Yes. HSE guidance says preference should go to competent people within your own organisation, and that can include the employer. For many small businesses, the owner with the right training and experience is the most sensible choice.
Who is responsible if the competent person gets it wrong?
The employer keeps the legal duty. Appointing a competent person, in-house or external, doesn't transfer your responsibilities under health and safety law. Individuals can also have their own duties, but you can't contract your way out of yours.
Is a RAMS drafted by software valid?
Whether a RAMS is suitable and sufficient depends on the site and the task, not on how the first draft was produced. A competent person must review, edit and approve any draft, from software or anywhere else, before work starts.
Official Resources
- MHSWR 1999, regulation 7: health and safety assistance (legislation.gov.uk)
- CDM 2015, regulation 8: general duties and competence (legislation.gov.uk)
- Getting competent help and assessing risks (HSE)
- Using a health and safety consultant or adviser (HSE)
- Training and competence (HSE)
- Occupational Safety and Health Consultants Register (OSHCR)
Recommended Tools & Resources
Save hours on health & safety paperwork — generate documents with swiftRMS.
Create a professional RAMS in under 2 minutes — UK legislation cited automatically.
From £49/mo. CDM 2015 referenced. 14-day free trial, no card needed.
The UK RAMS tools side by side: features, pricing and speed.
12+ trade-specific UK risk assessment templates with hazards and legislation.